1、 Irregular proportion

因為非正規廠家生產的模型產品未經航空公司、飛機制作廠授權，而是通過偽造正規廠家產品，或許通過互聯網上搜集的一些飛機圖片生產而成，因而模型的仿真程度相對較差、比例失調。正規廠家則是依據航空公司、飛機制作廠所供給圖紙生產模型。

Because the model products produced by informal manufacturers are not authorized by airlines and aircraft manufacturers, but are produced by forging the products of formal manufacturers, perhaps through some aircraft pictures collected on the Internet, the simulation degree of the model is relatively poor and out of proportion. Regular manufacturers produce models according to the drawings provided by airlines and aircraft manufacturers.

二、模型工藝差

Two, poor model process

1.外表容易黃、褪色

1. The appearance is easy to yellow and fade

正規生產廠家為確保產品的品質，在模型生產中所選用的都是價錢較貴的高等涂料，因而這種模型即便長時間存放也不容易涌現變黃、褪色等景象；而小企業以及非正規企業為了降低生產本錢則選用價錢低廉的涂料，這種涂料生產出來的模型剛開始與大廠家生產出來基礎無異，然而短則半年長則一年就會逐步涌現變黃、褪色的狀況，這也是為什么一些廠家能把價錢壓得更低的原因之一。

In order to ensure the quality of products, regular manufacturers choose expensive high-grade coatings in model production. Therefore, even if the model is stored for a long time, it is not easy to turn yellow and fade; In order to reduce the production cost, small enterprises and informal enterprises choose low-cost coatings. The model produced by this coating is just the same as that produced by large manufacturers. However, it will gradually turn yellow and fade in the short of half a year or a year. This is one of the reasons why some manufacturers can lower the price.

2.機翼、發起機等部件容易斷裂、脫離

2. The wing, engine and other components are easy to break and separate

小模型生產企業機非正規范圍型生產工藝的限制，以及為勤儉本錢而選用較差的材料的原因，他們所產生出來模型的機翼，發起機等部件咋運輸途中十分容易斷裂、脫離。這種損失率在成批的貨物運輸中可能相對較小，然而關于少量貨物的快遞運輸中這種損失率有時甚至于高達百分之七十以上。

Due to the limitations of informal range production process of small model manufacturers, and the reasons for choosing poor materials for diligence and thrift, the wings, initiators and other parts of the model they produce are very easy to break and separate during transportation. This loss rate may be relatively small in the transportation of bulk goods. However, in the express transportation of a small amount of goods, this loss rate is sometimes as high as more than 70%.

在互聯網上網站曾今涌現過為數眾多的此類模型零售銷售商，并低價銷售這些廠家的產品，然而因為高的運輸損失率以及前文所說的高的產品瑕疵率，大部分商家在銷售一段時間就紛繁關門或改行。

On the Internet, a large number of such model retail sellers have emerged on the website, and sell the products of these manufacturers at low prices. However, due to the high transportation loss rate and the high product defect rate mentioned above, most merchants close down or change their business after a period of sales.

3.外表不光滑、雜質較多

3. The surface is not smooth and there are many impurities

樹脂類飛機模型因為很多工序要通過手工完成，而一些廠家一味的尋求產量，降低本錢和產品價錢，這些模型往往缺少必要的質檢工序，成品模型中都會有一些存在瑕疵的產品混在當中。

Because many processes of resin aircraft models need to be completed manually, some manufacturers blindly seek output and reduce cost and product price. These models often lack necessary quality inspection processes, and some defective products will be mixed in the finished model.

這不是嚴峻影響產品的品質，對于模型經銷商來說盡量進貨價錢可能對比低，然而這樣高的瑕疵率不只不能把銷售價錢降低，也使得模型銷售銷售處于一種惡性循環當中，即：低的進貨價+高的瑕疵率=高的銷售價錢+低的客戶回頭率這也是為什么盡管潮汕地域的模型產業發展了十多年。然而各地的模型零售銷售商卻很少的原因之一。

This does not seriously affect the quality of products. For model dealers, the purchase price may be relatively low. However, such a high defect rate can not only reduce the sales price, but also make the model sales in a vicious circle, That is: low purchase price + high defect rate = high sales price + low customer return rate, which is why although the model industry in Chaoshan has developed for more than ten years. However, there are few model retailers everywhere, which is one of the reasons.